You can either remove the ballast or keep it, it’s not useful in this case anyway. Buy bulk and wholesale lighting products like recessed lighting, halogen light bulbs, fluorescent t5, fluorescent t8, metal halide, and high pressure sodium lamps and ballasts at great prices when you buy in quantity. Connect each blue wire of the driver to each lampholder at one end.
Philips EnduraLED T8 Tube LED Light Installation Guide
This guide explains the steps necessary to install or e tr of it ht8 ub lg and s p m performance.
Turn power circuit back on from breaker.
Please ensure only this end is installed in the powered lamp holder. Connect the black (l) and white (n) wires of driver to black and white wires of ac line, respectively. Sunco’s t8 18w led tube ballast pass (type b) install guide and manual. If not qualified, do not attempt installation.
(these contain mercury and need to be properly recycled) 3.
Wattage voltage current power factor. Cut the output wires on the ballast. Do not remove cover and/or end caps. Install the philips instantfit dimmable led t8.
T8 led tube light installation guide r installation / retrofit guide:
Lampholder sockets do not need to be replaced unless they are shunted, damaged, or missing. The led tube may be used in open or covered/lensed surface or recessed The new osram substitube product range provides tailored li. Power length type 8w06t8ww 25600020 warm white (3000k).
Lumens color temperature color rendering index (cri) beam angle.
Retrofit for t8 fluorescent tube; Remove lens, if applicable, remove fluorescent lamps and ballast cover. Verify that all contents of the retrofit kit are included. Make sure the portion of thetube.
Page 1 of 3 important safety instructions
Lampholders must be separated internally for proper wiring of the led tube. Power must be applied to the end cap labeled “ac input”. Close fixture and find your ac input side to led tube lamp. Make sure you cut off power before you start the installation procedure.
Led lights are bright, avoid looking directly to the led as extended exposure may cause harm to the eyes.
Any damaged parts prior to installation of the retroit kit. Up to 7% cash back philips instantfit dimmable led t8 lamps instructions 1. Instructions before installing hylite t8 led tube light. Applying power to wrong end will cause a direct short of the ac power when turned on.
Color rendering index ra＞80，good heat dissipation，low decay.
Disconnect power to the circuit at the breaker. • risk of electric shock! Ensure all power is off using a voltmeter or other method. Read the entire installation guide before proceeding on to the next step.
2.) inspect the t8 fa8 led tube for any damage or abnormality.
Ensure both the ends of the led tube are aligned with socket, then insert led lamp in the normal way by sliding pins into sockets and rotating a quarter turn until the led tube locks in place. Verify the fluorescent tube type is listed on the label of philips instantfit dimmable led t8 lamp. Led t8, ballast by pass —installation guide warnig: Led lamps are now fully installed.
Retrofit led t8 lamp installation guide step 1:
(if a starter is present remove as well) 4. This guide is for reference only and is intended for qualified electricians or lighting technicians. When the ac input side is attached to the ac power side on fixture, you are ready to go. Remove the existing fluorescent lamps from the luminaire.
Replace troffer lens, if present.
Connect them in series exactly as it shows 6.) install the led tube by placing the pins into the lampholders and turn clockwise. Installation this guide explains the steps necessary to install our t8 fa8 led tubes properly into your existing fixture to replace afluorescentt8fa8 tube. Using high brightness chip package led as light source uniformity lighting; Exxon lighting corporation isnotresponsibleforanydamage or harm caused by improper handing and installation.
Remove diffuser (if provided) 3.
Install the led tube by placing the pins into lamp holders and turn clockwise. Disconnect main power before installation. Led t8 installation guide author: Before installing make certain the power is off.
Please make sure the portion of the tube with the live end label is on the side where the wires are connected.
T8 linear led tube linear tube t8linearledtube *for multiple tubes; Install your new led tube. Not for use with dimmers. Then at the opposite end, connect the red wire of the driver to one lamp holder.
