Siamp Flush Valve Problems Sphinx Wisa Dual DF2 Twyford Wirquin

The toilet is a slim fitting batic from mfi about 12 months old. Siamp bcm 500/535 activation plate £17.00. It was fitted less than two years ago but never seemed quite right when new.

Slowfilling toilet, SIAMP fittings DIYnot Forums

Removing the duo flush valve from the seat.

The water flowing inside the bowl is the built in overflow system working , old toilets had a pipe to outside for water to drain if it was over filling , you said that your inlet valve was replaced so it may need some little adjustments so that the level of water in cistern is lower that should stop the water flowing in bowl , if not the flush part either needs adjustment which should be pretty.

Removing the activation box (both newer and older versions of the converter) once it has been snapped onto to the tank lever. I have another problem with the upstairs toilet. The only way to release it is to take cover off cistern an manually release it. What i'm confused about with this system is how the water is meant to stop.

I have replaced a worn out inlet diaphragm but it hasn't helped.

A new fill valve was less than £15 and was easy to fit, turn water off, flush loo, use sponge. Siamp has been innovating the sanitary industry for nearly 70 years with commitment to research and development. The fill valve of your toilet combines with the flush valve to ensure your toilet always has enough water to flush and keep everything clean. Just won't do a long flush at all.

I have had the same problem on a valve fitted 2 months ago replaced diaphragm today re ajusted level and still water level rising so i thought i would check to see if any body else having problem before contacting siamp.i have been a plumber for over 20 years.bring back the old fashioned ball valves.fit and forget!

However, now the flush will not flush at all! I'm having a few problems with a siamp flush which only seems to do a short flush. Im a homeowner, not a plummer and i have a siamp compact 99b cistern which won't stop filling up. Dudley flush flush valve problem valve;

No need to worry, a running toilet is usually a simple fix.

To find your nearest accredited siamp supplier who can provide you with a consultation, product or service, please enter your postcode. The button seemed to stick or click when pressed, but now refuses to do a long flush at all. Siamp toilet flush not working. Founded in 1947, siamp is a world leader in the design, manufacture and distribution of sanitary equipement.

Over 3 minutes to fill the cistern) we have 3.6 bar pressure.

Siamp has been innovating the sanitary industry for nearly 70 years with commitment to research and development. I unhooked the grey curved lever you can see at the front of the cistern to see if changing the height of this would work. The toilet in my new house was constantly trickling and as we are on a water meter i wanted to investigate the problem. The reason i ask is that our siamp fill rate has become very slow.

Common toilet fill valve problems + quick fixes.

Replace duo flush onto valve seat and turn on water, check for leaks. The down valve is playing up. Search 10 miles 20 miles 30 miles 50 miles 70 miles 100 miles everything Yes i know the rubber diaphragm gets a little tear in it and has to be replaced (£3.49 from b and q)but in.

Any ideas why it is not working?

The float is rising and is set at the correct height. Support frames, flush plates, flushing mechanisms, cisterns and seat covers. Status not open for further replies. Siamp dual flush button jamming on full flush?

The three most common causes are a broken or dirty flapper, too long or too short of a chain between the flush lever and the flapper or a float that is out of position.

The first thing you will need to do is turn off the water feeding into the toilet. I am confident i have installed it correctly however now the inlet valve will not shut off. I went to screwfix and purchased a new siamp washer. Founded in 1947, siamp is a world leader in the design, manufacture and distribution of sanitary equipement.

If you want to avoid having to fix these dastardly valves every few years, i would advise taking the things out and replacing them with something much more reliable.

After a flush water comes out of this hole as shown. Established in monaco in 1947 and with a presence in all five continents, siamp designs, manufactures and distributes a wide range of products and systems for toilets: The problem occurs either because the flapper is not seating itself correctly in the opening of the flush valve, or because the water level in the tank is too high and allows water to flow over the top of the overflow tube and down into the tank. The fill valve setup is a pretty simple one even when there are various types with different approaches on how to keep the toilet tank full.