1) operate the test/reset button 2) call your emergency services (fire dept. Not suitable for installation in hazardous locations as defined in the national electric code. Carbon monoxide alarm red, alarm.
How To Power Off Kidde Carbon Monoxide Detector Check
26 for “what to do when the alarm sounds” user’s guide.
This alarm will only indicate the presence of carbon monoxide gas at the sensor.
Thank you for purchasing the kidde combination photoelectric smoke and carbon monoxide alarm model 10sco. For best results, allow your unit. Do not reenter the premises nor move away from the open door/ It is not designed to detect any other gas.
Turn off the power to the smoke alarm at the circuit breaker.
Carbon monoxide may be present in other areas. Please read carefully and thoroughly • important: You might not require more get older to spend to go to the books commencement as capably as search for them. Apart from this, the co detector may also need to be reset even when it has not detected the presence of carbon monoxide.
Find smoke and carbon monoxide alarm, fire extinguisher manual, troubleshooting, alarm reset tips.
This carbon monoxide alarm is designed to detect carbon monoxide from any source of combustion. Please have the following information ready if you are calling customer service: Limitations of carbon monoxide alarms warning: 2) call your emergency services (fire department or 911);
Slide bracket on to screws then 0ghten.
Teach children how to respond to the alarms, and they should never play with the unit. Kidde home safety online help center for owners. 2b) if you believe that the source of carbon monoxide is not a gas appliance, contact either; Carbon monoxide:the alarm/voice pattern is four short alarm beeps followed by the verbal warning message “warning!
File type pdf kidde carbon monoxide alarm manual kn cob dp h kidde carbon monoxide alarm manual kn cob dp h this is likewise one of the factors by obtaining the soft documents of this kidde carbon monoxide alarm manual kn cob dp h by online.
Test the alarm to make sure it is working properly. Please take a few minutes to thoroughly read this user’s guide, which should be saved for future reference and passed on to any subsequent owner. Light will flash while in alarm/voice mode. This carbon monoxide alarm is designed to detect carbon monoxide gas from any source of combustion.
Next, locate the “reset” button for your specific model of carbon monoxide detector from the right side or from beneath its base.
Co alarm assembly number (located on. Do a head count to check that all persons are. How to reset a first alert smoke and carbon monoxide alarm. Carbon monoxide alarm procedure 1) operate the test/reset button;
2a) call the gas emergency services.
The led will flash every 2 seconds while the alarm is in hush mode. Poisonous gas other than carbon monoxide even though carbon monoxide can be generated by fire. Digital display and peak level memory. Co alarm model number (located on the back of alarm):
Kidde safety this manual and the products described in it are copyrighted,.
While powered by battery only, after four minutes the alarm/voice pattern will sound once every minute. First of all, do not rush to reset the co detector but step outside and expose yourself to fresh air. Test / reset reset power led button test/ carbon monoxide model: Insert the two fixings, that are supplied, into the holes.
It may also happen that the co detector continues to beep after detecting the presence of carbon monoxide.
Please take a few minutes to thoroughly read this user guide which should be saved for future reference. Press and release the test/reset button. When the carbon monoxide alarm sounds: Push and hold this button down for approximately 8 seconds after the alarm has been reset until it stops sounding.
It is not designed to detect smoke, fire, or any other gas.
Move to green, fresh air. Press and hold the test button for at least 15. This indicates that the alarm is set and working. This continues until the unit is reset or the co eliminated.
Using bracket as a guide, drill two holes in a wall 7cm (2 3/8”) apart.
Repeat with a number showing in the display (co concentration in ppm). 1) operate the test/reset button; Sometimes the co detector will give clear. After 15 seconds, there will be four quick beeps followed by five seconds of silence.
When the alarm condition goes away, the originating alarm unit will flash the led every 16 seconds until the test/reset button is pressed, thus resetting the alarm.
To reset a co detector, first, open a window. Move to fresh air peak level. Do a head count to check that all persons are accounted for. Ppm of co displayed lb= low battery end= end of unit life model:
